von cyrezzza » Fr 31. Okt 2014, 15:53
Hallo liebes Forum,
ich verfasse derzeit eine Ausarbeitung und möchte dort Blockschaltbilder einbinden. Nach kurzer Suche bin auch ich TikZ gestoßen. Die Grafiken, die
man damit erstellen kann sehen wirklich super aus. Mein Problem ist nur,
dass mir einfach die Zeit fehlt um mich in dem Maße einzuarbeiten, um das von mir gewünschte Blockschaltbild zu erzeugen.
ich habe allerdings schon was hinbekommen (dank Vorlagen und Internetrecherche). Ich bräuchte einfach nur noch ein paar kleine Hinweise, um ans Ziel zu kommen.
Das SOLL-Blockschaltbild habe ich in PP erstellt.
Leider funzt der Upload bei mir nicht
.
Daher erkläre ich es mal mit Worten.
Ich habe ein System aus 2 Blöcken. Der 1,. Block hat die Eingänge
vdq und vw. aus dem ersten Block kommt das Signal u1 und geht in den 2. Block. Zusätzlich gehen in den 2. Block noch die Signale u2 und u3.
In meinem bisherigen TikZ-Bild gehen die Größen u2 und u3 von "oben" auf den 2. Block. Da u2 und u3 aber keine Störgrößen sind sollen sie vo "links" in den Block reingehen und nicht von oben.
http://www.directupload.net/file/d/3792 ... fs_png.htm
Hier mein Latex Code
\documentclass[11pt, margin=0.5mm]{standalone}
\usepackage[bitstream-charter]{mathdesign}
%\usepackage[T1]{fontenc}
\usepackage{tikz}
\usetikzlibrary{shapes,arrows}
\usepackage{verbatim}
\begin{document}
\tikzstyle{block} = [draw, fill=blue!10, rectangle,
minimum height=3em, minimum width=6em]
\tikzstyle{sum} = [draw, fill=blue!10, circle, node distance=2cm]
\tikzstyle{input} = [coordinate]
\tikzstyle{output} = [coordinate]
\tikzstyle{pinstyle} = [pin edge={latex-,thin,black}]
\begin{tikzpicture}[auto, node distance=2cm,>=latex']
% We start by placing the blocks
\node [input, name=input] {};
\node [block, right of=input, pin={[pinstyle]above:$v_\mathrm{w}$}] (controller) {1. Teilsystem};
\node [block, right of=controller, pin={[pinstyle]above:$u_2, u_3$},
node distance=3.5cm] (system) {2. Teilsystem};
% We draw an edge between the controller and system block to
% calculate the coordinate u. We need it to place the measurement block.
\draw [->,>=latex] (controller) -- node[name=u1] {$u_1$} (system);
%\draw [->,>=latex] (controller) -- node[name=u23] {$u_2, u_3$} (system);
\node [output, right of=system] (output) {};
% Once the nodes are placed, connecting them is easy.
\draw [->,>=latex] (input) -- node {$\vec{v}_\mathrm{dq}$} (controller);
\end{tikzpicture}
\end{document}
Ich freue mich über jede Unterstützung.
Grüsse
cyrezzza
Hallo liebes Forum,
ich verfasse derzeit eine Ausarbeitung und möchte dort Blockschaltbilder einbinden. Nach kurzer Suche bin auch ich TikZ gestoßen. Die Grafiken, die
man damit erstellen kann sehen wirklich super aus. Mein Problem ist nur,
dass mir einfach die Zeit fehlt um mich in dem Maße einzuarbeiten, um das von mir gewünschte Blockschaltbild zu erzeugen.
ich habe allerdings schon was hinbekommen (dank Vorlagen und Internetrecherche). Ich bräuchte einfach nur noch ein paar kleine Hinweise, um ans Ziel zu kommen.
Das SOLL-Blockschaltbild habe ich in PP erstellt.
Leider funzt der Upload bei mir nicht :-(.
Daher erkläre ich es mal mit Worten.
Ich habe ein System aus 2 Blöcken. Der 1,. Block hat die Eingänge
vdq und vw. aus dem ersten Block kommt das Signal u1 und geht in den 2. Block. Zusätzlich gehen in den 2. Block noch die Signale u2 und u3.
In meinem bisherigen TikZ-Bild gehen die Größen u2 und u3 von "oben" auf den 2. Block. Da u2 und u3 aber keine Störgrößen sind sollen sie vo "links" in den Block reingehen und nicht von oben.
[url]http://www.directupload.net/file/d/3792/ok7fgzfs_png.htm[/url]
Hier mein Latex Code
[code]
\documentclass[11pt, margin=0.5mm]{standalone}
\usepackage[bitstream-charter]{mathdesign}
%\usepackage[T1]{fontenc}
\usepackage{tikz}
\usetikzlibrary{shapes,arrows}
\usepackage{verbatim}
\begin{document}
\tikzstyle{block} = [draw, fill=blue!10, rectangle,
minimum height=3em, minimum width=6em]
\tikzstyle{sum} = [draw, fill=blue!10, circle, node distance=2cm]
\tikzstyle{input} = [coordinate]
\tikzstyle{output} = [coordinate]
\tikzstyle{pinstyle} = [pin edge={latex-,thin,black}]
\begin{tikzpicture}[auto, node distance=2cm,>=latex']
% We start by placing the blocks
\node [input, name=input] {};
\node [block, right of=input, pin={[pinstyle]above:$v_\mathrm{w}$}] (controller) {1. Teilsystem};
\node [block, right of=controller, pin={[pinstyle]above:$u_2, u_3$},
node distance=3.5cm] (system) {2. Teilsystem};
% We draw an edge between the controller and system block to
% calculate the coordinate u. We need it to place the measurement block.
\draw [->,>=latex] (controller) -- node[name=u1] {$u_1$} (system);
%\draw [->,>=latex] (controller) -- node[name=u23] {$u_2, u_3$} (system);
\node [output, right of=system] (output) {};
% Once the nodes are placed, connecting them is easy.
\draw [->,>=latex] (input) -- node {$\vec{v}_\mathrm{dq}$} (controller);
\end{tikzpicture}
\end{document}
[/code]
Ich freue mich über jede Unterstützung.
Grüsse
cyrezzza